Froth-Pak insulation foam – the complete guide to the 180, 600 and 1900 kits

Looking for FROTH and wondering what hides behind the name? On the construction market it is shorthand for the original Froth-Pak insulation foam – a portable spray system used to create an airtight thermal and acoustic envelope in record time. In this article we look exclusively at the original kits supplied in 180, 600 and 1900 litre packs. You will learn how the Quick Rise (fast expansion) and Slow Rise (slow expansion) versions differ, what installers say about the product, and how to work safely with two-component PUR foam.

What is Froth-Pak?

Froth-Pak is a system built around two pressurised cylinders – one holding the isocyanate component, the other the polyol. The two react inside the spray gun and form a rigid, closed-cell polyurethane foam. The manufacturer points out that the new HFO-based formulation has a very low global warming potential (GWP). The kits are designed for fast insulation work: heat the cylinders, connect them to the gun and spray the foam without any external compressor. With a thermal conductivity (lambda) of 0.022 W/(m·K), the foam is among the best performing insulation materials on the market. Its R-value is around 0.45 m²·K/W per cm of thickness, which means even a thin layer delivers a high level of thermal protection.

What’s inside a Froth-Pak kit

Every Froth-Pak kit available in the 2K-Trade shop comes with two pressurised cylinders (single-use in the 180 and 600 versions, refillable in the 1900 version), the necessary hoses, a spray gun and a set of nozzles for different applications. The white cone nozzles are intended for standard spraying, the blue ones lay down a thin film, the green ones fill cracks and crevices, and the black ones are used to pour foam into larger cavities. The nozzles fit onto the spray gun and ensure even mixing of the two components. There are two formulations to choose from: Quick Rise (QR) – fast expansion – and Slow Rise (SR) – slow expansion. The QR version is tack-free in just 30 seconds and reaches full strength after about 5 minutes. The SR version takes around 60 seconds to take shape and roughly 8 minutes to cure fully, which gives the foam more time to flow into and fill enclosed spaces.

Key features and benefits

Outstanding insulation performance. Thanks to its low lambda value and high R-value, Froth-Pak insulates better than most traditional materials. Up to 95 % of the structure consists of closed cells, which makes the foam resistant to moisture and reduces condensation.

Fast installation, no extra equipment. No compressor, no power supply – simply heat the cylinders, connect the hoses and spray. The Quick Rise version cures in about 5 minutes, significantly cutting build time on site.

Versatile adhesion. The foam bonds to most substrates, including timber, concrete, steel, plasterboard and masonry, with the exception of a few plastics such as PE film and PTFE. It is waterproof and can also be used in cryogenic insulation.

Choice of formulation. Quick Rise (QR) is well suited to surface insulation – walls, roofs and lofts. Slow Rise (SR) is designed for filling enclosed cavities, for example in steel structures or OEM applications.

Greener formulation. The new recipe uses HFO blowing agents instead of HFCs, dramatically reducing the climate impact. The foam contains no formaldehyde or ozone-depleting substances.

Comparing the 180, 600 and 1900 kits

The table below summarises the key parameters of the three standard Froth-Pak kits. The data is taken from the official Fomicom manufacturer website.

Pack	Type	Expanded foam yield	Kit volume	Coverage at 5 cm	Gross weight	Application
Froth-Pak 180	single-use	375–430 l	≈ 0.4 m³	≈ 8 m²	~17 kg	Small projects and repairs, insulation around windows and thermal bridges
Froth-Pak 600	single-use	1250–1430 l	≈ 1.3 m³	≈ 26 m²	~25 kg	Mid-sized jobs – roofs, lofts, walls
Froth-Pak 1900	refillable	3900–4500 l	≈ 4.2 m³	≈ 84 m²	~95 kg	Large commercial projects, warehouses, cold stores; refillable

The 180 and 600 packs are available in either formulation (QR or SR), while the 1900 kit is normally supplied as a refillable system in either fast or slow expansion. The manufacturer also offers a mini kit (25–35 l), but this article focuses on the standard kits.

Quick Rise vs Slow Rise {#quick-vs-slow}

Quick Rise (QR) – the foam reaches its target volume in around 30 seconds and is tack-free almost immediately; full cure takes about 5 minutes. This rapid reaction makes QR ideal for vertical and horizontal surfaces such as walls, lofts and ceilings. It is the formulation of choice in residential construction, where speed and the option to apply several thin layers really matter.

Slow Rise (SR) – the foam needs about 60 seconds to take shape and around 8 minutes to cure completely. The longer reaction time lets the mass flow freely inside enclosed cavities, which is why SR is the right choice for injecting walls, suspended ceilings and for industrial and OEM manufacturing. When injecting, control the pressure carefully to avoid deforming the surrounding structure.

Parameter	Quick Rise	Slow Rise
Time to take shape	~30 s	~60 s
Full cure	~5 min	~8 min
Applications	Surface insulation – roofs, walls, ceilings	Filling enclosed cavities, injection
Advantages	Fast workflow, multi-layer application possible	Precise filling, lower risk of voids
Disadvantages	Short working time – requires experience	Longer cure and risk of overexpansion

Where Froth-Pak is used

• Residential building insulation: the foam is ideal for insulating roofs, ceilings, lofts, timber-frame walls, floors and thermal bridges. Its tightly closed cell structure is highly effective at eliminating draughts and cold bridges.
• Sealing joints and service penetrations: using injection nozzles, the foam fills gaps around pipes, HVAC ducts, ventilation runs and cable penetrations. It is also widely used to seal window and door frames.
• Industrial and OEM applications: SR kits are used to inject foam into machine housings, boats, trailers, refrigerated containers and steel structures. The foam provides insulation and structural stiffening at the same time.
• Renovation and refurbishment: Froth-Pak makes it possible to insulate lofts, top up insulation in older buildings and eliminate thermal bridges with minimal disruption to the existing structure.

If you are looking for ready-to-use kits, browse our shop: Froth-Pak 180 polyurethane foam insulation kit and Froth-Pak 600. We also stock the matching accessories: gun and hose kits, nozzles and heating jackets.

Step-by-step instructions

1. Prepare the cylinders and tools. Before starting, make sure the cylinders have reached a temperature of 25–30 °C. In cooler conditions, use a heating jacket to keep the cylinders at the correct working temperature.
2. Prepare the work area. Clean and dry the surface. Mask off any components that should not be coated and protect windows and services with masking tape.
3. Put on personal protective equipment. The operator should wear a hooded coverall, gloves, safety goggles and a half-mask respirator. Both isocyanate and polyol can irritate the skin and respiratory tract.
4. Connect the cylinders. Connect the red hose to cylinder A (isocyanate) and the blue hose to cylinder B (polyol). Fit the nozzle that matches your application and open the valves.
5. Test the system. Before spraying for real, fire a test shot into a bag or onto a piece of cardboard to confirm that the components are mixing evenly. If the foam colour is off, replace the nozzle.
6. Spraying. Hold the gun 30–50 cm from the surface and move it parallel to it. With Quick Rise, keep the gun moving at all times – pauses longer than 30 seconds can cause the nozzle to set. With Slow Rise, inject the foam slowly into the cavity and watch the expansion.
7. Cure time and finishing. Once the layer is applied, allow a few minutes for it to cure. When fully set, you can trim off any excess foam and cover it with a finish – plasterboard, render or paint. Remember that the foam is not UV resistant and must be covered when used outdoors.

Common questions and issues

Is Froth-Pak foam flammable? Like any organic product, cured foam will burn when in direct contact with a flame, but it does not sustain combustion – once the source of ignition is removed, the foam stops burning. The product is rated Euroclass E.

What are the safety rules? The manufacturer recommends reading the safety data sheet (SDS/MSDS). Wear protective clothing, goggles and a respirator, ensure good ventilation and keep the cylinders at working temperature.

Does the foam stick to every material? Froth-Pak bonds to most substrates: timber, metal, concrete and plaster. It does not, however, adhere to polyethylene (PE) or PTFE (Teflon), so any such films should be removed before spraying.

How do I work out how much foam I need? The manufacturer suggests a simple rule of thumb: surface area (m²) × insulation thickness (l/m²) = litres of foam. For example, a 100 m² roof requiring 8 cm of insulation (R ≈ 3.6) needs around 8,000 l of foam – for a project of this size it is worth considering a 1900 kit topped up with mini kits.

Is the foam waterproof and frost resistant? The foam is more than 95 % closed-cell and waterproof. It remains stable across a temperature range from –150 °C to +100 °C, which makes it suitable for refrigeration and cryogenic applications.

How long can a kit be stored? Single-use cylinders have a shelf life of approximately 15 months from the date of manufacture. After that, the components may begin to lose their properties.

Safety and precautions

• Suitable working conditions: store cylinders at 10–25 °C, away from heat sources and UV light. While spraying, ensure adequate ventilation to remove fumes.
• Personal protection: wear a coverall, goggles, gloves and a half-mask respirator with an A2/P3 filter; avoid contact with skin and eyes. Isocyanate can trigger allergic reactions and asthma, so sensitive individuals should take extra care.
• Avoid sources of fire and UV light: the foam is flammable when exposed to direct flame, and sunlight will yellow and degrade it. Outdoors, it must be covered with a protective layer (paint, render or cladding).
• Cleaning and maintenance: the GHA system (gun and hoses) can be cleaned and reused with the dedicated cleaning adapter. If the kit is left unused for an extended period, flush the hoses and discard any aged material to prevent clogging.

Pros and cons of Froth-Pak

Pros:

• Quick to install with no extra equipment – usable even on a site without electrical power.
• Excellent insulation in a thin layer: λ = 0.022 W/(m·K), R = 0.45 m²·K/W per cm.
• Resistant to water, mould and damp thanks to its closed-cell structure.
• Choice between fast and slow expansion to match the application.
• Greener HFO-based formulation with low GWP.

Cons:

• High kit price – on very large projects, hiring a professional spray-foam contractor may work out cheaper.
• Cylinder weight (17–95 kg) requires a trolley and is awkward to handle alone.
• Short working time of the QR formulation – experience is needed to avoid clogging the nozzles.
• Does not adhere to PE film or PTFE – such surfaces have to be prepared first.
• Flammable in direct flame – it must be protected with a finishing layer.

Alternatives and comparison

• Open-cell foams: cheaper and more flexible, but with a lower R-value and higher vapour permeability. They work well for acoustic insulation but are not moisture resistant.
• Single-component foams in cans: ideal for filling gaps around windows and doors, but they cannot deliver a continuous insulation layer or controlled thickness.
• Mineral wool and EPS: traditional materials are cheaper and easy to install, but they do not form an airtight barrier. Froth-Pak can be used as a “flash & batt” layer – a thin layer of foam combined with traditional mineral wool.
• Professional spray systems: on large projects it often pays to bring in a contractor with a high-pressure rig. Professionals deliver perfectly mixed foam and precise thickness, and the cost can be comparable to buying a large kit.

FAQ

What is the insulation value of Froth-Pak? The lambda value is 0.022 W/(m·K) and the R-value is approximately 0.45 m²·K/W per 1 cm of thickness. That puts the foam among the best performing insulation materials in its class.

What is included in the GHA kit? The gun-and-hose kit (GHA) includes a spray gun, hoses in 9, 15 or 30 ft lengths, nozzles, a spanner and technical petroleum jelly. All components can be cleaned and reused.

Is Froth-Pak compliant with EPB standards? Yes. The manufacturer states that its higher insulation performance compared with conventional materials helps buildings meet Energy Performance of Buildings (EPB) requirements.

Which kit should I choose – 180, 600 or 1900? The choice depends on the area and the required insulation thickness. For small repairs, the 180 kit is enough (around 8 m² at 5 cm); for mid-sized jobs, choose the 600 (around 26 m²); for large projects and industrial applications, go with the 1900 (around 84 m²).

What are the heating jackets for? Heating jackets keep the cylinders at the required working temperature (around 24 °C) when the ambient is cool, which improves foam yield and quality.

Summary

Froth-Pak insulation foam is a professional solution for the rapid insulation and air-sealing of buildings. The 180, 600 and 1900 kits differ in yield, weight and refillability, but they all rely on the same eco-friendly formulation with excellent insulation performance. Choosing between Quick Rise and Slow Rise lets you match the rate of expansion to the type of project. Before starting work, prepare carefully, wear the right personal protective equipment and follow the manufacturer’s recommendations. Used correctly, Froth-Pak delivers durable, airtight insulation – even in hard-to-reach places.

If you are planning a purchase, take a look at our Froth-Pak 180 and Froth-Pak 600 kits, along with the accompanying nozzles, gun and hose kits and heating jackets in our shop. That way you can pick the right kit for your project and achieve a professional result.

{ “@context”: “https://schema.org”, “@type”: “FAQPage”, “mainEntity”: [ { “@type”: “Question”, “name”: “What is the difference between Froth-Pak 180, 600 and 1900?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “The kits differ in yield: the 180 produces about 4.2 m3 of foam, the 600 about 14 m3 and the 1900 about 44 m3. The larger the kit, the lower the cost per cubic metre.” } }, { “@type”: “Question”, “name”: “Is Froth-Pak suitable for insulating behind stretch ceilings?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “Yes, Froth-Pak is excellent for insulating the void above the stretch ceiling membrane, improving both acoustics and thermal performance of the room.” } }, { “@type”: “Question”, “name”: “How long can a kit be used after opening?”, “acceptedAnswer”: { “@type”: “Answer”, “text”: “Once the hoses are connected the kit must be used within 30 minutes. Unused material in the cylinders retains its properties for up to 30 days.” } } ] }